![Drifting lands metacritic](https://loka.nahovitsyn.com/101.jpg)
![controlplane mac alternative controlplane mac alternative](https://www.macupdate.com/images/icons512/39644.png)
![controlplane mac alternative controlplane mac alternative](https://alternative.me/media/512/mission-control-thumbnail-me992hsrygerou7b-c.png)
Older Docker Installations (untested, known to have bugs).Kubectl Version Skew (Kubernetes limits supported version skew).reach out and ask for help in #kind on the kubernetes slack.file an issue (if there isn't one already).10.0.0.Having problems with kind? This guide covers some known problems and solutions / workarounds. Pings time out, even when I specify the ping 10.0.0.93 -I enp13s0f0 I am only attempting to ping server1 from server 3 or vice versa. Let me know what other output from the server would be useful and if there are any other troubleshooting commands that I should use to figure out. THANK YOU very much for taking the time to read through this all and help out. Input rate 177.31 Kbps, 346 pps output rate 264 bps, 0 ppsĠ unicast packets 16162771 multicast packets 0 broadcast packetsĠ jumbo packets 0 storm suppression bytesģ8 input error 0 short frame 0 overrun 0 underrun 0 ignoredĠ watchdog 0 bad etype drop 0 bad proto drop 0 if down dropĠ unicast packets 25648 multicast packets 0 broadcast packetsĠ output error 0 collision 0 deferred 0 late collisionĠ lost carrier 0 no carrier 0 babble 0 output discard Last clearing of "show interface" counters 12:57:24ģ0 seconds input rate 177568 bits/sec, 346 packets/secģ0 seconds output rate 504 bits/sec, 0 packets/sec Input flow-control is off, output flow-control is off Reliability 255/255, txload 1/255, rxload 1/255Īuto-Negotiation is turned on, FEC mode is Auto VLAN MAC Address Type age Secure NTFY Ports (T) - True, (F) - False, C - ControlPlane MAC * - primary entry, G - Gateway MAC, (R) - Routed MAC, O - Overlay MACĪge - seconds since last seen,+ - primary entry using vPC Peer-Link, !Command: show running-config interface Ethernet1/5ĩ3180A(config-if)# show mac address-table int eth1/5 Switch A interface config and stats and mode.
![controlplane mac alternative controlplane mac alternative](https://machow2.com/wp-content/uploads/2018/09/visio-alternatives-for-mac-cover.jpg)
#Controlplane mac alternative manual#
**please assume the commands entered were correct - typing this manually**Įnp13s0f0 and enp13s0f0 are inet manual like the rest of the portsīond_xmit_hash_policy layer2+ qdisc mq state DOWN group default qlen 1000 link/ether 00:00:c9:85:0f:7e brd ff:ff:ff:ff:ff:ff inet 10.0.0.91/24 brd 10.0.0.255 scope global enp13s0f0 valid_lft forever preferred_lft forever Here's what I initially configured and what I saw on both server/switch side: Single purpose is for the Ceph network (VLAN 599).Setup server 1 and 3's 2 x 10gbps NICs as LACP and vPC on the Nexus end.Here's what I was initially trying to accomplish: As I've been reading on, I don't know if that's possible. I wanted to bond 8 of these to get 8gbps hopefully for the Ceph network. Server #2 has a 4 x Gig-E card and a 2 x Gig E card. NICs - 2 port CNA (Mellanox I believe, maybe HP branded) I'm trying to ditch the LACP idea and see if I can get a single 10gbps port working on Server 1 and 3 Please read through, but start with the basics. I have the OS installed and nothing has been modified yet other than the NIC settings. Hello! I'm trying to cluster 3 servers together.
![Drifting lands metacritic](https://loka.nahovitsyn.com/101.jpg)